Similar
CAPE CANAVERAL, Fla. – In the Space Station Processing Facility at NASA's Kennedy Space Center in Florida, technicians check the nitrogen tank assembly closely as an overhead crane lifts and moves it to the Express Logistics Carrier 1, or ELC-1. The carrier is part of the STS-129 payload on space shuttle Atlantis, which will deliver to the International Space Station two spare gyroscopes, two nitrogen tank assemblies, two pump modules, an ammonia tank assembly and a spare latching end effector for the station's robotic arm. STS-129 is targeted to launch Nov. 12. Photo credit: NASA/Jim Grossmann KSC-2009-4712
CAPE CANAVERAL, Fla. – In Orbiter Processing Facility-3 at NASA's Kennedy Space Center in Florida, members of the STS-130 crew inspect space shuttle Endeavour's payload bay. In the right corner, from left are Commander George Zamka, Pilot Terry Virts Jr. and Mission Specialist Robert Behnken. The crew is at Kennedy for a crew equipment interface test, or CEIT, which provides hands-on training and observation of shuttle and flight hardware. The STS-130 flight will carry the Tranquility pressurized module with a built-in cupola to the International Space Station aboard Endeavour. Launch is targeted for Feb. 4, 2010. Photo credit: NASA/Kim Shiflett KSC-2009-6143
CAPE CANAVERAL, Fla. – In Orbiter Processing Facility 2 at NASA's Kennedy Space Center, STS-126 Commander Chris Ferguson (left) and Mission Specialists Shane Kimbrough and Steve Bowen get a close look at hardware inside space shuttle Endeavour's payload bay. Members of space shuttle Endeavour's STS-126 crew are at Kennedy to participate in a crew equipment interface test, or CEIT. The CEIT provides experience handling tools, equipment and hardware they will use on the mission. Endeavour will deliver a multi-purpose logistics module to the International Space Station on the STS-126 mission. Launch is targeted for Nov. 10. Photo credit: NASA/Kim Shiflett KSC-08pd2253
KENNEDY SPACE CENTER, FLA. - In the Orbiter Processing Facility bay 1 at NASA Kennedy Space Center, engineers stand by as the remote manipulator system, or boom, is lowered toward Atlantis’ payload bay for installation. Atlantis is the designated orbiter for mission STS-115, the 19th assembly flight to the International Space Station. The payload includes the P3/P4 solar arrays. The launch planning window has not been determined yet for STS-115. KSC-06pd0012
STS-133 R2 ROBONAUT CONTAINER LIFT TO PMM 2010-4447
KENNEDY SPACE CENTER, FLA. -- The STS-111 crew looks at the replacement pitch roll joint for the SSRMS (Canadarm 2) they will be installing on the mission to the International Space Station. The crew comprises Commander Kenneth Cockrell, Pilot Paul Lockhart, and Mission Specialists Franklin Chang-Diaz and Phillippe Perrin, who is with the French Space Agency. Part of the payload on mission STS-111 is the Mobile Base System (MBS), which will be installed on the Mobile Transporter to complete the Canadian Mobile Servicing System, or MSS. The mechanical arm will then have the capability to "inchworm" from the U.S. Lab Destiny to the MSS and travel along the truss to work sites. STS-111 is the second utilization flight (UF-2) to the Space Station and will also carry the Expedition 5 crew to replace Expedition 4. Launch is scheduled for May 30, 2002 KSC-02pd0555
CAPE CANAVERAL, Fla. – In the space Station Processing Facility at NASA's Kennedy Space Center in Florida, technicians attach the overhead crane to the pump module orbital replacement unit. The crane will lift and move the equipment to the Express Logistics Carrier 1, or ELC-1. The carrier is part of the STS-129 payload on space shuttle Atlantis, which will deliver to the International Space Station two spare gyroscopes, two nitrogen tank assemblies, two pump modules, an ammonia tank assembly and a spare latching end effector for the station's robotic arm. STS-129 is targeted to launch Nov. 12. Photo credit: NASA/Jim Grossmann KSC-2009-4721
Hubble Space Telescope (HST) at Lockheed Facility during preflight assembly
KENNEDY SPACE CENTER, FLA. - STS-118 Mission Specialist Scott Parazynski (left) practices using a tool that is part of equipment for the mission to the International Space Station. Below is Mission Specialist Dafydd Williams (Canadian Space Agency). At right is STS-116 Mission Specialist Christer Fuglesang (European Space Agency), also taking part in the equipment familiarization. The STS-118 mission will be delivering and installing the third starboard truss segment, the ITS S5, to the International Space Station, and carry a SPACEHAB Single Cargo Module with supplies and equipment. The STS-116 mission will deliver the third port truss segment, the P5 Truss, to attach to the second port truss segment, the P3/P4 Truss. Launch dates for both missions are under review. KSC-04pd0878
Related
THEMIS SPACECRAFT - Public domain NASA photogrpaph
THEMIS SPACECRAFT - Public domain NASA photogrpaph
THEMIS SPACECRAFT - Public domain NASA photogrpaph
THEMIS SPACECRAFT - Public domain NASA photogrpaph
THEMIS SPACECRAFT - Public domain NASA photogrpaph
THEMIS SPACECRAFT - Public domain NASA photogrpaph
THEMIS SPACECRAFT - Public domain NASA photogrpaph
THEMIS SPACECRAFT - Public domain NASA photogrpaph
THEMIS SPACECRAFT - Public domain NASA photogrpaph
THEMIS SPACECRAFT - Public domain NASA photogrpaph
Summary
The original finding aid described this as:
Description: NASA's Time History of Events and Macroscale Interactions during Substorms (THEMIS) SPACECRAFT LOCATED IN THE SWALES AEROSPACE CLEANROOM..
Photographer: CHRIS GUNN
Date: 1/30/2006
Job Number: 2006-00591-0
Preservation Copy: .tif
2006
Nothing Found.
Tags
themis
spacecraft
nasa
high resolution
themis spacecraft
swales aerospace cleanroom
macroscale interactions
chris gunn
job number
preservation copy
space program
Date
2006 - 2011
Source
The U.S. National Archives
Link
Copyright info
No known copyright restrictions