Similar
KENNEDY SPACE CENTER, FLA. - In the Space Shuttle Main Engine (SSME) Processing Facility, Boeing-Rocketdyne technicians prepare to move SSME 2058, the first SSME fully assembled at KSC. Move conductor Bob Brackett (on ladder) and technicians secure a sling around the engine under the direction of crane operator Joe Ferrante (left). The engine will be lifted from its vertical work stand into a horizontal position in preparation for shipment to NASA’s Stennis Space Center in Mississippi to undergo a hot fire acceptance test. It is the first of five engines to be fully assembled on site to reach the desired number of 15 engines ready for launch at any given time in the Space Shuttle program. A Space Shuttle has three reusable main engines. Each is 14 feet long, weighs about 7,800 pounds, is seven-and-a-half feet in diameter at the end of its nozzle, and generates almost 400,000 pounds of thrust. Historically, SSMEs were assembled in Canoga Park, Calif., with post-flight inspections performed at KSC. Both functions were consolidated in February 2002. The Rocketdyne Propulsion and Power division of The Boeing Co. manufactures the engines for NASA. KSC-04pd1642
S113E05117 - STS-113 - ISS views - PMA2, U.S. Lab, SSRMS, AL, and S0 Truss during Docking Operations for STS-113
CAPE CANAVERAL, Fla. – In the Space Shuttle Main Engine Processing Facility at NASA’s Kennedy Space Center in Florida, preparations are under way to install a Pratt Whitney Rocketdyne space shuttle main engine (SSME) into a transportation canister. This is the second of the 15 engines used during the Space Shuttle Program to be prepared for transfer to NASA's Stennis Space Center in Mississippi. The engines will be stored at Stennis for future use on NASA's new heavy-lift rocket, the Space Launch System (SLS), which will carry NASA's new Orion spacecraft, cargo, equipment and science experiments to space. For more information, visit http://www.nasa.gov/shuttle. Photo credit: NASA/Gianni Woods KSC-2012-1017
Related
KENNEDY SPACE CENTER, FLA. -- In Orbiter Processing Facility bay 3 at NASA's Kennedy Space Center, technicians on a Hyster forklift move space shuttle main engine no. 1 toward Endeavour for installation. Each space shuttle main engine is 14 feet long, weighs about 6,700 pounds, and is 7.5 feet in diameter at the end of the nozzle. The orbiter is targeted for launch on Feb. 14 for mission STS-123 to the International Space Station. Photo credit: NASA/Jack Pfaller KSC-07pd3302
KENNEDY SPACE CENTER, FLA. -- In Orbiter Processing Facility bay 3 at NASA's Kennedy Space Center, technicians on a Hyster forklift maneuver space shuttle main engine no. 1 into place on Endeavour. Each space shuttle main engine is 14 feet long, weighs about 6,700 pounds, and is 7.5 feet in diameter at the end of the nozzle. The orbiter is targeted for launch on Feb. 14 for mission STS-123 to the International Space Station. Photo credit: NASA/Jack Pfaller KSC-07pd3304
KENNEDY SPACE CENTER, FLA. -- In Orbiter Processing Facility bay 3 at NASA's Kennedy Space Center, technicians on a Hyster forklift maneuver space shuttle main engine no. 1 into place on Endeavour. Each space shuttle main engine is 14 feet long, weighs about 6,700 pounds, and is 7.5 feet in diameter at the end of the nozzle. The orbiter is targeted for launch on Feb. 14 for mission STS-123 to the International Space Station. Photo credit: NASA/Jack Pfaller KSC-07pd3306
KENNEDY SPACE CENTER, FLA. -- In Orbiter Processing Facility bay 3 at NASA's Kennedy Space Center, technicians on a Hyster forklift move space shuttle main engine no. 1 toward Endeavour for installation. Each space shuttle main engine is 14 feet long, weighs about 6,700 pounds, and is 7.5 feet in diameter at the end of the nozzle. The orbiter is targeted for launch on Feb. 14 for mission STS-123 to the International Space Station. Photo credit: NASA/Jack Pfaller KSC-07pd3301
KENNEDY SPACE CENTER, FLA. -- In Orbiter Processing Facility bay 3 at NASA's Kennedy Space Center, technicians on a Hyster forklift maneuver space shuttle main engine no. 1 into place on Endeavour. Each space shuttle main engine is 14 feet long, weighs about 6,700 pounds, and is 7.5 feet in diameter at the end of the nozzle. The orbiter is targeted for launch on Feb. 14 for mission STS-123 to the International Space Station. Photo credit: NASA/Jack Pfaller KSC-07pd3303
KENNEDY SPACE CENTER, FLA. -- In Orbiter Processing Facility bay 2, technicians on a Hyster forklift maneuver space shuttle main engine no. 3 into place on Endeavour. Each space shuttle main engine is 14 feet long, weighs about 6,700 pounds, and is 7.5 feet in diameter at the end of the nozzle. The orbiter is scheduled for mission STS-118, targeted for launch on June 28. The mission will be the 22nd flight to the International Space Station, carrying another starboard array, S5, for installation. Photo credit: NASA/George Shelton KSC-07pd0134
KENNEDY SPACE CENTER, FLA. -- In Orbiter Processing Facility bay 2, technicians on a Hyster forklift install space shuttle main engine no. 3 into Endeavour. Each space shuttle main engine is 14 feet long, weighs about 6,700 pounds, and is 7.5 feet in diameter at the end of the nozzle. The orbiter is scheduled for mission STS-118, targeted for launch on June 28. The mission will be the 22nd flight to the International Space Station, carrying another starboard array, S5, for installation. Photo credit: NASA/George Shelton KSC-07pd0133
KENNEDY SPACE CENTER, FLA. -- In Orbiter Processing Facility bay 2, technicians on a Hyster forklift maneuver space shuttle main engine no. 3 into place on Endeavour. Each space shuttle main engine is 14 feet long, weighs about 6,700 pounds, and is 7.5 feet in diameter at the end of the nozzle. The orbiter is scheduled for mission STS-118, targeted for launch on June 28. The mission will be the 22nd flight to the International Space Station, carrying another starboard array, S5, for installation. Photo credit: NASA/George Shelton KSC-07pd0135
KENNEDY SPACE CENTER, FLA. -- In the Orbiter Processing Facility, STS-123 Mission Specialist Richard Linnehan practices with tools that will be used on the mission. He and other crew members are at NASA's Kennedy Space Center for a crew equipment interface test, a process of familiarization with payloads, hardware and the space shuttle. The STS-123 mission is targeted for launch on space shuttle Endeavour on Feb. 14. It will be the 25th assembly flight of the station. Photo credit: NASA/Kim Shiflett KSC-07pd3569
KENNEDY SPACE CENTER, FLA. -- In Orbiter Processing Facility bay 3 at NASA's Kennedy Space Center, technicians on a Hyster forklift maneuver space shuttle main engine no. 1 into place on Endeavour. Each space shuttle main engine is 14 feet long, weighs about 6,700 pounds, and is 7.5 feet in diameter at the end of the nozzle. The orbiter is targeted for launch on Feb. 14 for mission STS-123 to the International Space Station. Photo credit: NASA/Jack Pfaller KSC-07pd3305
Summary
KENNEDY SPACE CENTER, FLA. -- In Orbiter Processing Facility bay 3 at NASA's Kennedy Space Center, technicians on a Hyster forklift maneuver space shuttle main engine no. 1 into place on Endeavour. Each space shuttle main engine is 14 feet long, weighs about 6,700 pounds, and is 7.5 feet in diameter at the end of the nozzle. The orbiter is targeted for launch on Feb. 14 for mission STS-123 to the International Space Station. Photo credit: NASA/Jack Pfaller
The Space Shuttle program was the United States government's manned launch vehicle program from 1981 to 2011, administered by NASA and officially beginning in 1972. The Space Shuttle system—composed of an orbiter launched with two reusable solid rocket boosters and a disposable external fuel tank— carried up to eight astronauts and up to 50,000 lb (23,000 kg) of payload into low Earth orbit (LEO). When its mission was complete, the orbiter would re-enter the Earth's atmosphere and lands as a glider. Although the concept had been explored since the late 1960s, the program formally commenced in 1972 and was the focus of NASA's manned operations after the final Apollo and Skylab flights in the mid-1970s. It started with the launch of the first shuttle Columbia on April 12, 1981, on STS-1. and finished with its last mission, STS-135 flown by Atlantis, in July 2011.
Nothing Found.
Tags
kennedy space center
orbiter
bay
facility bay
technicians
hyster
forklift
maneuver
hyster forklift maneuver space shuttle
engine
endeavour
space shuttle
diameter
nozzle
sts
mission sts
international space station
jack
pfaller
high resolution
nasa
Date
13/11/2007
in collections
Location
Source
NASA
Link
Copyright info
Public Domain Dedication (CC0)