Similar
Lights illuminate an XM230E1 30mm chain gun/cannon mounted on a test stand and a blast test composite panel at the Rock Island Arsenal
CONSTRUCTION IN THE ENGINE RESEARCH BUILDING ERB SOUTHWEST SW WING AND THE OUTSIDE DRIVE FOUNDATIONS
CAPE CANAVERAL, Fla. – Inside Orbiter Processing Facility-1 at NASA’s Kennedy Space Center in Florida, United Space Alliance technicians monitor the progress of space shuttle Atlantis’ payload bay doors as they are closed in preparation for its move to the Vehicle Assembly Building. The work is part of the Space Shuttle Program’s transition and retirement processing of the space shuttle fleet. A groundbreaking was held Jan. 18 for Atlantis’ future home, a 65,000-square-foot exhibit hall in Shuttle Plaza at the Kennedy Space Center Visitor Complex. Atlantis is scheduled to roll over to the visitor complex in November in preparation for the exhibit’s grand opening in July 2013. For more information, visit http://www.nasa.gov/shuttle. Photo credit: NASA/Dimitri Gerondidakis KSC-2012-3482
KENNEDY SPACE CENTER, FLA. - Workers in the Payload Hazardous Servicing Facility look over the aeroshell enclosing Mars Exploration Rover 2 and lander that is being moved to a rotation table for a spin stabilization test. There are two identical rovers that will land at different regions of Mars and are designed to cover roughly 110 yards each Martian day over various terrain. Each rover will carry five scientific instruments that will allow it to search for evidence of liquid water that may have been present in the planet's past. The first rover, MER-A, is scheduled to launch June 5 from Cape Canaveral Air Force Station. The second is scheduled for launch June 25. KSC-03pd1370
CAPE CANAVERAL, Fla. – In Orbiter Processing Facility-1 at NASA’s Kennedy Space Center in Florida, United Space Alliance technicians monitor the alignment of the forward reaction control system onto space shuttle Atlantis during the system’s reinstallation on the shuttle. The system helped the shuttle maneuver while it was in orbit. Atlantis’ FRCS was removed and sent to White Sands Test Facility in New Mexico to be cleaned of its toxic propellants. The work is part of the Space Shuttle Program’s transition and retirement processing of the shuttle fleet. A groundbreaking was held Jan. 18 for Atlantis' future home, a 65,000-square-foot exhibit hall in Shuttle Plaza at the Kennedy Space Center Visitor Complex. Atlantis is scheduled to roll over to the visitor complex in November in preparation for the exhibit’s grand opening in July 2013. For more information, visit http://www.nasa.gov/shuttle. Photo credit: NASA/Jim Grossmann KSC-2012-3099
CAPE CANAVERAL, Fla. – In Orbiter Processing Facility 1 at NASA's Kennedy Space Center in Florida, workers remove the reinforced-carbon carbon, or RCC, panels from the wing leading edge on space shuttle Atlantis. The structural edge of the wing (area of red and green behind the panels) will undergo spar corrosion inspection to verify the structural integrity of the wing. The RCC panels will be placed in protective coverings until the inspection is complete. Atlantis will make the 31st flight to the International Space Station for the STS-129 mission, targeted for launch on Nov. 12. Photo credit: NASA/Tim Jacobs KSC-2009-3829
A left side view of the ETU-111/E multipurpose trailer used for the KC-135R Stratotanker aircraft re-engine program. The trailer frame is in a raised position, the wheels are pinned and the cradle is level. This trailer is used to transport the KC-135R engine
CAPE CANAVERAL, Fla. --- In Orbiter Processing Facility Bay 3 at NASA's Kennedy Space Center, space shuttle Discovery's payload bay door at right is nearly closed. Below the door is the shuttle's robotic arm. Discovery is the designated vehicle on the STS-124 mission to the International Space Station. On the mission, the shuttle will transport the Kibo Japanese Experiment Module - Pressurized Module and the Japanese Remote Manipulator System. The payload will be installed at the launch pad. Launch is targeted for May 25. Photo credit: NASA/Chris Rhodes KSC-08pd0876
Survey instrument outside the Bevatron. Photograph taken October 20, 1958. Bevatron-1615
Related
GEAR FATIGUE AND SPIRAL BEVEL GEAR TEST FACILITY GRC-1998-C-02777
GEAR FATIGUE AND SPIRAL BEVEL GEAR TEST FACILITY GRC-1998-C-02776
FIBERS TEST FACILITY AND SAMPLES GRC-1998-C-00593
FIBERS TEST FACILITY AND SAMPLES GRC-1998-C-00596
FIBERS TEST FACILITY AND SAMPLES GRC-1998-C-00595
FOIL BEARING TEST JOURNAL GRC-2003-C-00392
DYNAMIK DES DROPLET COMBUSTIONS UND ERWEITERUNGSTEST HARDWARE GRC-2001-C-00424
FOOL AIR BEARINGS FÜR TEST JOURNAL GRC-2002-C-00975
AKOUSTISCHE TEST-LABOR-RIBBON-SCHNEIDUNG UND TEAM-ANERKENNUNG GRC-2000-C-01529
GEAR FATIGUE AND SPIRAL BEVEL GEAR TEST FACILITY GRC-1998-C-02778
Zusammenfassung
GEAR FATIGUE AND SPIRAL BEVEL GEAR TEST FACILITY
Tags
grc
Glenn-Forschungszentrum
Ausrüstung
Ermüdung
Getriebeermüdung
Spiral-
Prüfung
Getriebeprüfstand grc
hohe Auflösung
NASA
Datum
10/11/1999
Quelle
NASA
Link
Copyright-info
Public Domain Dedication (CC0)